激光器驱动电路中英文翻译

《激光器驱动电路中英文翻译》由会员分享，可在线阅读，更多相关《激光器驱动电路中英文翻译（9页珍藏版）》请在毕设资料网上搜索。

1、1 中文 2540 字 Laser driver circuit Small changes will directly semiconductor laser drive current to the output intensity fluctuation. To stabilize the output power semiconductor laser, Voltage negative feedback principle to design a constant current driving circuit comprises a soft starting and curren

2、t limiting protection circuit based on； At the same time, according to the need of the light source is modulated to eliminate the influence of background light and, integrated laser modulation circuit comprises a crystal oscillation circuit and divider circuit design. Making the specific circuit and

3、 complete the relevant experimental. The experimental results show that the circuit can provide a driving current of high stability, Current stability up to 0.05%； Soft start and current-limiting protection circuit can protect the semiconductor laser and enhance the impact capability. Modulation cir

4、cuit generates a carrier signal needed for laser diode modulation and direct to complete the output light modulation, The switch can be conveniently realized from 256Hz to 512kHz range of 12 kinds of commonly used modulation frequency selection. Semiconductor laser with its excellent characteristics

5、, high efficiency, simple structure, small is widely used in scientific research, national defense, medical, and other areas of processing, its drive technology becomes more and more important. Semiconductor laser is the ideal electron - photon direct conversion devices, quantum efficiency is very h

6、igh, the current small changes will lead to a great change, the output light intensity of the therefore, semiconductor laser drive current requirements is very high. Driving technology of semiconductor laser usually adopts constant current drive mode, this work, through the principle of negative fee

7、dback control loop, directly provide the effective control of the drive current. In addition, the transient current or voltage spikes, and overcurrent, overvoltage will damage the semiconductor laser drive circuit, therefore should be considered in the protection circuit against electric shock measu

8、res and special. In some applications, DC semiconductor lasers produce DC drive light in the measurement process is vulnerable to interference from ambient light slow change, which could not be separated from the environment light required DC optical signal, the signal-to-noise ratio is too small, s

9、o to carry on the modulation. When the high-speed modulated semiconductor lasers, there will be dynamic characteristics is 2 complex, such as the relaxation oscillation, since the pulse and multi-pulse phenomena. In this paper, experiments were conducted to study the characteristics of low frequency

10、 modulation. Semiconductor laser output is stable, and can be directly modulated, it has been widely applied in optical system, is the preferred source sensor system. This paper describes the design of a high stability driving current, modulation, simple operation and low cost driving circuit for th

11、e light source of optical fiber systems. In this paper, the design of driving the semiconductor laser modulation circuit composed of four parts, including constant current circuit, a soft start, current limit protection and modulation signal generating circuit. The constant current circuit to genera

12、te a high stable drive current. Soft start is the role of eliminating surge may be present in the circuit, to prevent the harm of surge for laser. To avoid damage due to overcurrent caused by semiconductor laser can not be restored, then adding current-limiting protection in a driver circuit. Circui

13、t to realize the modulation and frequency can be adjusted to generate a modulated signal. The constant current circuit is shown in figure 1, The in-phase end voltage reference Vr into A1 op amp, the operational control amplifier conducting level, and thus to obtain the corresponding output current.

14、The output current generated by sampling voltage sampling resistor Rs, the sampling voltage is amplified as the inverting input voltage feedback voltage feedback amplifier A1, and voltage and the in-phase input end of comparison, Q2 to adjust the output voltage through the triode, adjustment and out

15、put current of semiconductor lasers, so that the whole closed-loop feedback system in the dynamic balance. Figure 1 Constant current map Because the switch instantaneous in power supply generates a voltage, current surge, as well as the surge interference effects are likely to cause the breakdown an

16、d 116AR81 16R 6 A5.1KA1O P A M PA R ?O P A M P+ 1 2 V12U7l a s e rQ22 N 2 2 2 2 AR71K- 1 2 VVr1 16R 5 A1M3 the damage of the semiconductor laser, and therefore must be in the design of soft start circuit drive laser, namely the use of the charge and discharge of RC circuit, delay time, the specific

17、circuit as shown in Figure 2 as shown in. Switch S1 is closed, the current through the resistor R1 and capacitor C3 to charge, the base electrode of the triode Q voltage gradually rises. As the capacitor charging and the conduction of the triode, output voltage Vo is achieved from 0 to the maximum r

18、ise slowly, until the capacitor charge saturation, the voltage and current stabilizing. When the power supply is disconnected, the process of reverse, so as to realize the current and voltage decreases slowly. Figure 2 Soft start circuit diagram Laser soft start time and the charging capacitor and t

19、he corresponding resistance, when the capacitor charging tends to saturation, the output voltage soft start circuit can achieve maximum. Power supply voltage is V I, the capacitor voltage is Vo, the capacitor charging formula: 10 (1 )RCiV V e According to this formula can calculate the electric char

20、ge and discharge time. Semiconductor laser with other devices, have normal working current, if the current exceeds this range, the laser will be damaged, therefore must restrict current laser in the set range. Emitter voltage transistor Q2 as the feedback voltage terminal phase in A3 op amp, when th

21、e feedback voltage is less than the limit voltage V, A3 op amp output low level, the transistor Q1 is turned on, this time by a triode Q2 output voltage feedback voltage is greater than the limit； when the voltage of V, A3 op amp output high, triode Q1 cutoff, this limits the triode Q2 emission increases very current, and is limited to a specific value. So even if the current caused by Vr control voltage exceeds the set V i n1GND2V ou t3U178 L 05C6105C2104C3105S1R11MV0Q2N 22 22 A