外文翻译---数控机床开环控制伺服系统

《外文翻译---数控机床开环控制伺服系统》由会员分享，可在线阅读，更多相关《外文翻译---数控机床开环控制伺服系统（6页珍藏版）》请在毕设资料网上搜索。

1、The open system merit of Computer Numerical Control The open system merit is the system simple, the cost low, but the shortcoming is the precision is low. The reverse gap, the guide screw pitch error, stop inferiorly can affect the pointing accuracy by mistake. Following several kind of improvements

2、 measure may cause the pointing accuracy distinct improvement. 1. reverse gap error compensates The numerical control engine bed processing cutting tool and the work piece relative motion is depends upon the drive impetus gear,the guide screw rotation, thus the impetus work floor and so on moves the

3、 part to produce moves realizes. As traditional part gear, guide screw although the manufacture precision is very high, but always unavoidably has the gap. As a result of this kind of gap existence, when movement direction change, starts the section time to be able to cause inevitably actuates the p

4、art wasting time, appears the instruction pulse to push the motionless functional element the aspect. This has affected the engine bed processing precision, namely the instruction pulse and actual enters for the step does not tally,has the processing error therefore, the split-ring numerical control

5、 system all establishes generally has the reverse gap error compensatory function, with by makes up which wastes time the step reverse gap difference compensates is first actual reverse enters for the error, converts the pulse equivalent number it, compensates the subroutine as the gap the output, w

6、hen the computer judgment appears when instruction for counter motion, transfers the gap to compensate the subroutine immediately, compensates the pulse after the output to eliminate the reverse gap to carry on again normally inserts makes up the movement. 2. often the value systematic characteristi

7、c position error compensates A kind of storehouse by transfers for the designer. Like this in the components design stage, the designer only must input the characteristic the parameter, the system direct production characteristic example model: We must save the related characteristic class in the da

8、tabase the structure information, the database table collection are use in saving this part of related information. According to the characteristic type definition need, we defined the characteristic class code table, the characteristic class edition information have outstanding shown the characteri

9、stic type； Defined the characteristic class structure outstanding to reach the characteristic class the structure； And relates through the components characteristic disposition table and the components characteristic level information. The characteristic level data sheet collection is this component

10、s model database design core, has recorded characteristic example information and so on model design, craft. The characteristic structure table has recorded the characteristic geometry structure； The characteristic size table, the characteristic shape position table of limits, the characteristic sur

11、face roughness table has recorded the characteristic project semantics quotation； The size table, the shape position table of limits, the surface roughness table saved all components characteristic data message. In the characteristic level, using characteristic ID, geometry principal linkage and so

12、on essential factor ID, size ID, common difference ID, roughness ID carries on the data retrieval. We apply this components information model database under the factory environment some module CAD in the AM integrative system, has realized CAD and the CAPP characteristic information sharing well. Ma

13、in use ready-made CAD/the CAM software (Unigra phics 1I) carries on the product design and the NC programming in this system, and through carries on two times of developments gains components to this software the size information； At the same time uses the dialogue window which develops voluntarily,

14、 lets design the personnel to input other characteristic information alternately, realizes this software and the system sharing database connection. When assistance technological design, the technological design personnel through the procedure inquiry function, inquires the components information fr

15、om the sharing database which needs, carries on the interactive technological design. Thus has facilitated the CAPP components information acquisition, enhanced the technological design efficiency. When carries on the NC programming using UG, may from the sharing database gain the craft and the manu

16、facture information which needs, carries on various working procedures the knife axle design and the processing simulation establishes an absolute zero spot on the numerical control engine bed, the actual various coordinate axes syzygy completely position error, makes the curve in order to determine

17、d compensates the spot. Attempts l to show is an actual position error curve, (error) carries on this curve y-coordinate take the pulse equivalent as the unit the division, makes the horizontal line, each horizontal line and the curve point of intersection namely compensates the spot for the goal. C

18、hart 1 the center 1 to 6 oclock place position errors for, needs to do reduces the pulse to compensate； But needs to carry on 6 to 9 adds the pulse to compensate in the chart the shadow partially for to compensate the area. Compensates the range of points these to become the error The calibration co

19、rrections stores the computer, when work table by zero displacement in position, installs sends out the absolute zero point localization signal in the absolute zero point micros witch, later computer as necessary will send out the goal to compensate to compensate the signal, will carry on the positi

20、on error to the engine bed to compensate. The cosine generator assigns slide guage initiation signal a electricity and by step of transmission. 3. feedbacks compensates the open-loop control Chart 2 has produced this kind of system schematic diagram. This system surveys two parts by the open-loop co

21、ntrol and the induction synchromesh direct position to be composed. Here position examination does not serve as the position the feedback, but is compensates the feedback as the position error. Its cardinal principle is: Installs the instruction pulse by the engine bed numerical control which CNC se

22、nds out, on the one hand the supplies open system, the control step-by-steps the electrical machinery according to the instruction revolution, and the direct drive platen moves, constitutes the open-loop control； On the other hand this instruction pulse supplies the induction synchromesh the measure

23、ment system (namely digitally, cosine generator), as position demand signal a by. The work in the warning way induction synchromesh this time not only is the position sensor, also is the comparator, it by, The cosine generator assigns slide guage initiation signal a electricity and by step of transm

24、ission. 4. conclusions Under the CIMS environment the technology which develops unceasingly based on characteristic components information modeling, how enhances the components order of complexity which the characteristic design can complete； How causes question and so on request which the character

25、istic design adoption trick recognition, the characteristic semantics transforms also to wait for the people to solve. This article introduced the characteristic technology in the components information modeling application, describes this components data model database realization with emphasis； Es

26、tablishes the components information database system may satisfy the CIMS system well to the letter. Reference: 1.Zhang Huashu under. parallel environment based on characteristic components definition model J. mechanical science with technology, 1,999, 18 (1): 14l 144. 2.forest morning star, Du full text, Xu Jianxin. characteristic and (,M)/CAPP/CAM