外文翻译---土压力理论在薄煤层回填支柱设计中的应用

《外文翻译---土压力理论在薄煤层回填支柱设计中的应用》由会员分享，可在线阅读，更多相关《外文翻译---土压力理论在薄煤层回填支柱设计中的应用（10页珍藏版）》请在毕设资料网上搜索。

1、翻译部分 英文原文 Design of backfilled thin-seam coal pillars usingearth pressure theory 1. Introduction The Self-Advancing Miner has been designed to extract coal from seams less than 90centimeters thick. The SAM allows for extraction of the fullseam height while minimizing waste rock, and utilizes remote

2、operation that allowsthe miner to advance up to 180m (600ft) into the seam. However, the coal seams areso thin that the recovery rates of this mining method will be fairly low and willdecrease rapidly with the depth of mining. In order to increase the recovery fromthin-seam mines, pillars must be de

3、signed as small as possible withoutcompromising the stability of the mine. Backfill can provide the support necessaryto maintain the integrity of the underground workings while allowing for increasedextraction. The placing of backfill underground has predominantly been a practice employedin cut-and-

4、fill mines (Thomas, 1979). Backfill material is introduced undergroundinto previously mined stopes to provide a working platform and localized support,reducing the volume of open space which could potentially be filled by a collapseof the surrounding pillars (Barret et al., 1978). The presence of fi

5、ll in an openingprevents large-scale movements and collapse of openings merely by occupying voidsleft by mining (Aitchison et al.1973).Therefore, the placement of fill in open spacesunderground tends to prevent the unraveling/spalling of the surrounding rock massinto the mined-out space, effectively

6、 increasing the strength, or load bearingcapacity, of the surrounding rock mass. This type of support mechanism not onlyhelps provide support to pillars and walls, but also helps to prevent caving and rooffalls, minimize surface subsidence, and enhance pillar recovery (Coates, 1981). Although the su

7、pport capability of backfill is well known it still remains fairlydifficult to quantify. Models and equations for the determination of backfill supporthave been proposed (Cai, 1983； Guang-Xu and Mao-Yuan, 1983) and pillar-backfillsystems have been modeled using laboratory set-ups in order to correla

8、te the actualsupport behavior of fill with proposed models (Yamaguchi and Yamatomi, 1989；Blight and Clarke, 1983； Swan and Board, 1989； Aitchison et al., 1973). But ingeneral these models and lab tests are dependent on local experience and empiricallyderived relationships between backfill support, m

9、aterial properties, and minegeometry. Since the SAM is still in development there is a need for a simple andreliable method of estimating the magnitude of support provided by backfill basedon existing knowledge. It is proposed that classical earth pressure theory can be usedto estimate the lateral e

10、arth pressure applied by backfill. The anticipated behaviorand response of fill to deformations of the surrounding pillars and roof are analyzedhere. The supporting effect of backfill is incorporated into the original pillar design(unsupported) so that new pillar widths can be calculated and the inc

11、rease inrecovery can be determined. 2. The thin-seam coal mine A thin-seam coal mine, employing the SAM technology, can be thought of as an underground highwall mine. Figure 1 depicts the simplified panel geometry createdby the development of entries and cross-cuts, and the system of pillars left be

12、hind afterpanel extraction. It is probable that the cuts and cross-cuts will be angledat approximately 60so as to decrease the turning radius of mining equipment, butthis will not effect pillar design. The length of each panel is 1200m (4000ft).The width of each panel varies with depth in order to accommodate a barrier pillarthat runs through the center of each panel. However, the panel width will be at leastGreaterthantwicethedistancerequiredforoneSAMcut,inthiscase300m(1000ft).Upo