毕业设计--日产5000吨水泥熟料生产线（粉磨）工艺设计

《毕业设计--日产5000吨水泥熟料生产线（粉磨）工艺设计》由会员分享，可在线阅读，更多相关《毕业设计--日产5000吨水泥熟料生产线（粉磨）工艺设计（63页珍藏版）》请在毕设资料网上搜索。

1、洛阳理工学院毕业设计 I 日产 5000 吨 水泥熟料生产线（粉磨）工艺设计 参数 2 摘 要 本设计是针对 5000t/d 熟料新型干法生产线（粉磨 ）的工艺设计， 水泥粉磨是水泥制造的最后工序， 其主要功能在于将水泥熟料 (及缓凝剂、性能调节材料等 )粉磨至适宜的粒度 (以细度、比表面积等表示 )，形成一定的颗粒级配，增大其水化面积，加速水化速率，满足水泥浆体凝结，硬化要求。 本次设计 在 配料计算 基础上，进行了 物料平衡 、储库平衡、主机平衡 计算 ，并以此为依据，对全厂储库 、主机及辅机 进行了 选型 和工艺布置 ； 重点对水泥粉磨 进行了工艺计算、设备规格设计、工艺布置 设计 。

2、采用的是目前大多数大型水泥生产线水泥粉磨系统的优选方案之一，即带辊压机的挤压联合水泥粉磨系统， 最大限度的降低能耗 ，设计熟料烧成能耗 2950kJ/kg， 减少基建投资，又最大限度的提高产量、质量，做到环保，技术经济指标先进、合理。 关键词 ： 水泥厂 设计 , 水泥挤压联合粉磨 ， 球磨机 ， 辊压机 洛阳理工学院毕业设计 II 5000 T/D CEMENT CLINKER PRODUCTION LINE ( GRINDING) PROCESS DESIGN-TWO PARAMETERS ABSTRACT This design is aim at the end of kiln tec

3、hnics for 5000t/d ripe material new type dry process calcinations workshop. Cement grinding is at the end of the cement manufacture process. Its main function is to cement clinker grinding to suitable particle. Form certain particle grading. Increase its hydration area, accelerate the hydration rate

4、, and satisfy the Cement slurry condensation, the hardening requirements. This design carried on the material balance, reservoir balance and host balance calculation which were based on the calculation of the ingredients, and as a basis, the whole plant reservoir, main and auxiliary machinery having

5、 been selected and carried on the layout process； and then it was carried on the process calculation, equipment specification design, process layout design which were focus on the Cement grinding. Using the most current large-scale cement production line cement grinding system one of the preferred o

6、ptions, with a roller press to squeeze the Joint cement grinding system, it could maximum decrease the energy consumption, energy consumption for clinker design 2950kJ/kg, investment of capital construction, in the same time, it also maximum enhance the yield and quality, satisfy the requirement of protecting environment and make the technical economic index advanced and reasonable. KEY WORDS: cement clinker design, cement extrusion joint grinding, ball mill，roller press