制动系统外文翻译

《制动系统外文翻译》由会员分享，可在线阅读，更多相关《制动系统外文翻译（5页珍藏版）》请在毕设资料网上搜索。

1、附 录 1 BRAKE SYSTEM The braking system is the most important system in cars. If the brakes fail, the result can be disastrous. Brakes are actually energy conversion devices, which convert the kinetic energy (momentum) of the vehicle into thermal energy (heat). The brake system is composed of the foll

2、owing basic components: the “master cylinder” 、 “brake lines” 、 “brake hoses” 、 “slave cylinders” . “brake disk” “filler block” and so on. The typical brake system consists of disk brakes in front and either disk or drum brakes in the rear connected by a system of tubes and hoses that link the brake

3、 at each wheel to the master cylinder . Stepping on the brake pedal, a plunger is actually been pushing against in the master cylinder which forces hydraulic oil (brake fluid) through a series of tubes and hoses to the braking unit at each wheel. Since hydraulic fluid (or any fluid for that matter)

4、cannot be compressed, pushing fluid through a pipe is just like pushing a steel bar through a pipe. Unlike a steel bar, however, fluid can be directed through many twists and turns on its way to its destination, arriving with the exact same motion and pressure that it started with. It is very import

5、ant that the fluid is pure liquid and that there are no air bubbles in it. Air can compress, which causes a sponginess to the pedal and severely reduced braking efficiency. If air is suspected, then the system must be bled to remove the air. There are “bleeder screws” at each wheel cylinder and cali

6、per for this purpose. With drum brakes, fluid is forced into the wheel cylinder which pushes the brake shoes out so that the friction linings are pressed against the drum which is attached to the wheel, causing the wheel to stop. On a disk brake, the fluid from the master cylinder is forced into a c

7、aliper where it presses against a piston. The piston, in-turn, squeezes two brake pads against the disk(rotor)which is attached to the wheel, forcing it to slow down or stop. This process is similar to a bicycle brake where two rubber pads rub against the wheel rim creating friction. In either case,

8、 the friction surfaces of the pads on a disk brake system, or the shoes on a drum brake convert the forward motion of the vehicle into heat. Heat is what causes the friction surfaces (linings) of the pads and shoes to eventually wear out and require replacement. Drum Brakes So if disk brakes are so

9、great, how come we still have cars with drum brakes? The reason is cost. While all vehicles produced for many years have disk brakes on the front, drum brakes are cheaper to produce for the rear wheels. The main reason is the parking brake system. On drum brakes, adding a parking brake is the simple

10、 addition of a lever, while on disk brakes, we need a complete mechanism, in some cases, a complete mechanical drum brake assembly inside the disk brake rotor! Parking brakes must be a separate system that does not use hydraulics. It must be totally mechanical, but more on parking brakes later Wheel

11、 Cylinder The wheel cylinder consists of a cylinder that has two pistons, one on each side. Each piston has a rubber seal and a shaft that connects the piston with a brake shoe. When brake pressure is applied, the pistons are forced out pushing the shoes into contact with the drum. Wheel cylinders m

12、ust be rebuilt or replaced if they show signs of leaking. Brake Shoes Like the disk pads, brake shoes consist of a steel shoe with the friction material or lining riveted or bonded to it. Also like disk pads, the linings eventuallywear out and must be replaced. If the linings are allowed to wear thr

13、ough to the bare metal shoe, they will cause severe damage to the brake drum. Backing Plate The backing plate is what holds everything together. It attaches to the axle and forms a solid surface for the wheel cylinder, brake shoes and assorted hardware. It rarely causes any problems Reading material

14、： Disk Brake Disk brakes, like many automotive innovations, were originally developed for auto racing, but are now standard equipment on virtually every car made. On most cars, the front brake are of the disc type, and the rear brakes are of the “drum” type. Drum brakes use two semi-circular shoes t

15、o press outward against the inner surfaces of a steel drum. Older cars often had drum brakes on all four wheels, and many new have 4-wheel disc brakes. Though disc brakes rely on the same basic principles to slow a vehicle (friction and heat), their design is far superior to that of drum brakes. Bec

16、ause disc brakes can fling off water more easily than drum brakes, they work much better in wet conditions. This is not to say that water does not affect them, it definitely does. If you splash through a puddle and then try to apply the brakes, your brakes may not work at all for a few seconds！ Disc

17、 brakes also allow better airflow cooling, which also increases their effectiveness. Some high performance disc brakes have drilled or slotted holes through the face of the rotor, which helps to prevent the pads from “glazing” (becoming hardened due to heat). Disc brakes were introduced as standard equipment on most cars in the early seventies.