基于单片机数字电压表电路设计外文翻译

《基于单片机数字电压表电路设计外文翻译》由会员分享，可在线阅读，更多相关《基于单片机数字电压表电路设计外文翻译（13页珍藏版）》请在毕设资料网上搜索。

1、北京化工大学北方学院毕业设计（论文） 外文文献原稿和译文 1 外文文献原稿 和译文 原 稿 Front side Copyright of this circuit belongs to smart kit electronics. In this page we will use this circuit to discuss for improvements and we will introduce some changes based on original schematic General Description This is an easy to build, but neve

2、rtheless very accurate and useful digital voltmeter. It has been designed as a panel meter and can be used in DC power supplies or anywhere else it is necessary to have an accurate indication of the voltage present. The circuit employs the ADC (Analogue to Digital Converter) I.C. CL7107 made by INTE

3、RSIL. This IC incorporates in a 40 pin case all the circuitry necessary to convert an analogue signal to digital and can drive a series of four seven segment LED displays directly. The circuits built into the IC are an analogue to digital converter, a comparator, a clock, a decoder and a seven segme

4、nt LED display driver. The circuit as it is described here can display any DC voltage in the range of 0-1999 Volts. Technical Specifications - Characteristics Supply Voltage: . +/- 5 V (Symmetrical) Power requirements: . 200 mA (maximum) Measuring range: . +/- 0-1,999 VDC in four ranges Accuracy: .

5、0.1 % FEATURES Small size Easy construction 北京化工大学北方学院毕业设计（论文） 外文文献原稿和译文 2 Low cost. Simple adjustment. Easy to read from a distance. Few external components. How it Works In order to understand the principle of operation of the circuit it is necessary to explain how the ADC IC works. This IC has th

6、e following very important features: Great accuracy. It is not affected by noise. No need for a sample and hold circuit. It has a built-in clock. It has no need for high accuracy external components. Schematic (fixed 16-11-09) 北京化工大学北方学院毕业设计（论文） 外文文献原稿和译文 3 7-segment display pinout MAN6960 An Analog

7、ue to Digital Converter, (ADC from now on) is better known as a dual slope converter or integrating converter. This type of converter is generally preferred over other types as it offers accuracy, simplicity in design and a relative indifference to noise which makes it very reliable. The operation o

8、f the circuit is better understood if it is described in two stages. During the first stage and for a given period the input voltage is integrated, and in the output of the integrator at the end of this period, there is a voltage which is directly proportional to the input voltage. At the end of the

9、 preset period the integrator is fed with an internal reference voltage and the output of the circuit is gradually reduced until it reaches the level of the zero reference voltage. This second phase is known as the negative slope period and its duration depends on the output of the integrator in the

10、 first period. As the duration of the first operation is fixed and the length of the second is variable it is possible to compare the two and this way the input voltage is in fact compared to the internal reference voltage and the result is coded and is send to the display. All this sounds quite eas

11、y but it is in fact a series of very complex operations which are all made by the ADC IC with the help of a few external components which are used to configure the circuit for the job. In detail the circuit works as follows. The voltage to be measured is applied across points 1 and 2 of the circuit and through the circuit R3, R4 and C4 is finally applied to pins 30 and 31 of the IC. These are the