毕业设计-- 铜氨液、再生气回流塔的设计

《毕业设计-- 铜氨液、再生气回流塔的设计》由会员分享，可在线阅读，更多相关《毕业设计-- 铜氨液、再生气回流塔的设计（44页珍藏版）》请在毕设资料网上搜索。

1、 上海应用技术学院 机械工程学院 毕业设计（论文） 题目 铜氨液、再生气回流塔的设计 学生姓名 徐骏 专 业 过程装备与控制工程 学 号 0910221130 班 级 09102211 指导教师 朱柳娟 职 称 讲师 2013 年 6 月铜氨液、再生气回流塔的设计 摘要： 此次设计回流塔的介质为铜氨液、再生气，塔的设计温度为 100，设计压力为0.18MPa，塔径 1400mm，塔高 11.25m，填料塔，填料段： 1。塔设备是生产过程中一种重要的单元操作设备，它广泛应用于化工、炼油、医药、食品及环境保护等工业部门。本铜氨液、再生气回流塔的作用是利用铜氨液对再生气中所含的少量一氧化碳和二氧化碳

2、进行脱洗 。首先考虑到工艺条件等因素，塔体的材料选用了 Q345R。其次对塔进行了强度和稳定性校核，计算了质量载荷，塔的自振周期、地震载荷与地震弯矩、风载荷与风弯矩。进行了圆筒轴向应力校核和裙座轴向应力校核。通过计算得出强度和稳定性都符合要求。然后通过比较不同的元件，分别对吊柱、吊耳、填料、设备接管、法兰、平台及扶梯进行了设计选择。最后利用 Fluent 软件对该回流塔进行上段液体流动分析，检验回流塔上段液体流动是否满足均匀分布要求。 关键词：填料塔；铜氨液；再生气；压力容器； Fluent Design of Cuprammonia and Resurgent gases Reflux Co

3、lumn Abstract： The media of this design of cuprammonia and resurgent gases column is cuprammonia and resurgent gases,and its design temperature is 100 ,design pressure is 0.18MPa.The diameter of column is 1400mm,and height is 11.75m,which is packing layer and has 1 trays.Column is an important proce

4、ss equipment,which is widely used in petrochemical,pharmacy,food,environment protection and so on.The cuprammonia and resurgent gases column is to use cuprammonia wash off a small amount of carbon monoxide and carbon dioxide contained in the regeneration gas.Based on process conditions,Q345R was cho

5、sen as column material.Stiffening was made at open pore region and stiffening rings was chosen.The strength and the stability of the column were checked including calculating mass loads,self-vibrations cycles,earthquake loads,earthquake moments,wind loads,wind moments.The axial stresses in cylindric

6、al shell and skirt support were checked.The strength and the stability of the column were eligible.And by comparing different components,davits,sag,trays,tubes,flanges,flats and ladders were designed and chosen.Finally,Fluent6.3.26 which is used to analysis has been used for check the liquid. KeyWords： Packed tower； Cuprammonia； Resurgent gass； Prseesur； fluent