数字温度传感器毕业论文中英文资料外文翻译

《数字温度传感器毕业论文中英文资料外文翻译》由会员分享，可在线阅读，更多相关《数字温度传感器毕业论文中英文资料外文翻译（14页珍藏版）》请在毕设资料网上搜索。

1、中英文资料外文翻译文献 1 中文 3340 字 外文资料 DS1722 Digital Thermometer With scientific and technological progress and development of the types of temperature sensors increasingly wide range of application of the increasingly widespread, and the beginning analog toward digital, single -bus, dual-bus and bus-3 direc

2、tion. And the number of temperature sensors because they apply to all microprocessor interface consisting of automatic temperature control system simulation can be overcome sensor and microprocessor interface need signal conditioning circuit and A / D converters advantages of the drawbacks, has been

3、 widely used in industrial control, electronic transducers, medical equipment and other temperature control system. Among them, which are more representative of a digital temperature sensor DS18B20, MAX6575, the DS1722, MAX6636 other. This paper introduces the DS1722 digital temperature sensor chara

4、cteristics, the use of the method and its timing. Internal structure and other relevant content. FEATURES: Temperature measurements require no external components； Measures temperatures from -55C to +120C. Fahrenheit equivalent is -67F to +248F； Thermometer accuracy is 2.0C； Thermometer resolution i

5、s configurable from 8 to 12 bits (1.0C to 0.0625C resolution)； Data is read from/written to via a Motorola Serial Peripheral Interface (SPI) or standard 3-wire serial interface； Wide analog power supply range (2.65V - 5.5V)； Separate digital supply allows for 1.8V logic； Available in an 8-pin SOIC (

6、150 mil), 8-pin USOP, and flip chip package； PIN ASSIGNMENT 中英文资料外文翻译文献 2 FIGURE 1 PIN ASSIGNMENT PIN DESCRIPTION: SERMODE - Serial Interface Mode. CE - Chip Enable. SCLK - Serial Clock. GND Ground. VDDA - Analog Supply Voltage. SDO - Serial Data Out. SDI - Serial Data In. VDDD - Digital Supply Volt

7、age. DESCRIPTION: The DS1722 Digital Thermometer and Thermostat with SPI/3-Wire Interface provides temperature readings which indicate the temperature of the device. No additional components are required； the device is truly a temperature-to-digital converter. Temperature readings are communicated f

8、rom the DS1722 over a Motorola SPI interface or a standard 3-wire serial interface. The choice of interface standard is selectable by the user. For applications that require greater temperature resolution, the user can adjust the readout resolution from 8 to 12 bits. This is particularly useful in a

9、pplications where thermal runaway conditions must be detected quickly. For application flexibility, the DS1722 features a wide analog supply rail of 2.65V - 5.5V. A separate digital supply allows a range of 1.8V to 5.5V. The DS1722 is available in an 8-pin SOIC (150-mil), 8-pin USOP, and flip chip p

10、ackage. Applications for the DS1722 include personal computers/servers/workstations, cellular telephones, office equipment, or any thermally-sensitive system. OVERVIEW: 中英文资料外文翻译文献 3 A block diagram of the DS1722 is shown in Figure 2. The DS1722 consists of four major components: 1. Precision temper

11、ature sensor. 2. Analog-to-digital converter. 3. SPI/3-wire interface electronics. 4. Data registers. The factory-calibrated temperature sensor requires no external components. The DS1722 is in a power conserving shutdown state upon power-up. After power-up, the user may alter the configuration regi

12、ster to place the device in a continuous temperature conversion mode or in a one-shot conversion mode. In the continuous conversion mode, the DS1722 continuously converts the temperature and stores the result in the temperature register. As conversions are performed in the background, reading the te

13、mperature register does not affect the conversion in progress. In the one-shot temperature conversion mode, the DS1722 will perform one temperature conversion, store the result in the temperature register, and then eturn to the shutdown state. This conversion mode is ideal for power sensitive applic

14、ations. More information on the configuration register is contained in the “OPERATION-Programming” section. The temperature conversion results will have a default resolution of 9 bits. In applications where small incremental temperature changes are critical, the user can change the conversion resolu

15、tion from 9 bits to 8, 10, 11, or 12. This is accomplished by programming the configuration register. Each additional bit of resolution approximately doubles the conversion time. The DS1722 can communicate using either a Motorola Serial Peripheral Interface (SPI) or standard 3-wire interface. The us

16、er can select either communication standard through the SERMODE pin, tying it to VDDD for SPI and to ground for 3-wire. The device contains both an analog supply voltage and a digital supply voltage (VDDA and VDDD, respectively). The analog supply powers the device for operation while the digital supply provides the top rails for the digital inputs and outputs. The DS1722 was designed to be 1.8V Logic-Ready.