车床毕业论文外文翻译

《车床毕业论文外文翻译》由会员分享，可在线阅读，更多相关《车床毕业论文外文翻译（13页珍藏版）》请在毕设资料网上搜索。

1、 毕业设计译文 题 目 : 矿井提升及总体设计 学生姓名： 杜雨航 准考证号： 080112200473 指导老师： 张冬梅 2012 年 LATHES The basic machines that are designed primarily to do turning, facing and boring are called lathes. Very little turning is done on other types of machine tools, and nine can do it with equal facility. Because lathe can do bo

2、ring, facing, drilling, and reaming in addition to turning, their versatility permits several operations to be performed with a single setup of the workpiece. This accounts for the fact that lathes of various types are more widely used in manufacturing than any other machine tool. Lathes in various

3、forms have existed for more than two thousand years. Modem lathes date from about 1797, when Henry Maudsley developed one with a leadscrew. It provided controlled, mechanical feed of the tool. This ingenious Englishman also developed a change-gear system that could connect the motions of the spindle

4、 and leadscrew and thus enable threads to be cut. Lathe Construction. The essential components of a lathe are depicted in the block diagram of Fig.15-1.These are the bed, headstock assembly, tailstock assembly, carriage assembly, quick-change gear box, and the leadscrew and feed rod. The bed is the

5、backbone of a lathe. It is usually made of well-normalized or aged gray or nodular cast iron and provides a heavy, rigid frame on which all the other basic components are mounted. Two sets of parallel, longitudinal ways, inner and outer, are contained on the bed, usually on the upper side. Some make

6、rs use an inverted V-shape for all four ways, whereas others utilize one inverted V and one flat way in one or both sets. Because several other components are mounted and/or move on the ways they must be made with precision to assure accuracy of alignment. Similarly, proper precaution should be take

7、n in operating a lathe to assure that the ways are not damaged. Any inaccuracy in them usually means that the accuracy of the entire lathe is destroyed. The ways on most modern lathes are surface hardened to offer greater resistance to wear and abrasion. The headstock is mounted in a fixed position

8、on the inner ways at one end of the lathe bed. It provides a powered means of rotating the work at various speeds. It consists, essentially, of a hollow spindle, mounted in accurate bearings, and a set of transmission gears-similar to a truck transmission-through which the spindle can be rotated at

9、a number of speeds. Most lathes provide from eight to eighteen speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained merely by moving from two to four levers. An increasing trend is to provide a continuously variable speed range through electrical or mechanical dr

10、ives. Because the accuracy of a lathe is greatly dependent on the spindle, it is of heavy construction and mounted in heavy bearings, usually preloaded tapered roller or ball types. A longitudinal hole extends through the spindle so that long bar stock can be fed through it. The size of this hole is

11、 an important size dimension of a lathe because it determines the maximum size of bar stock that can be machined when the material must be fed through the spindle. The inner end of the spindle protrudes from the gear box and contains a means for mounting various types of chucks, face plates, and dog

12、 plates on it. Whereas small lathes often employ a threaded section to which the chucks are screwed, most large lathes utilize either cam-lock or key-drive taper noses. These provide a large-diameter taper that assures the accurate alignment of the chuck, and a mechanism that permits the chuck or fa

13、ce plate to be locked or unlocked in position without the necessity of having to rotate these heavy attachments. Power is supplied to the spindle by means of an electric motor through a V-belt or silent-chain drive. Most modern lathes have motors of from 5 to 15 horsepower to provide adequate power

14、for carbide and ceramic tools at their high cutting speeds. The tailstock assembly consists, essentially, of three parts. A lower casting fits on the inner ways of the bed and can slide longitudinally thereon, with a means for clamping the entire assembly in any desired location. An upper casting fi

15、ts on the lower one and can be moved transversely upon it on some type of keyed ways. This transverse motion permits aligning the tailstock and headstock spindles and provides a method of turning tapers. The third major component of the assembly is the tailstock quill. This is a hollow steel cylinde

16、r, usually about 2 to 3 inches in diameter, that can be moved several inches longitudinally in and out of the upper casting by means of a handwheel and screw. The open end of the quill hole terminates in a Morse taper in which a lathe center, or various tools such as drills, can be held. A graduated

17、 scale, several inches in length, usually is engraved on the outside of the quill to aid in controlling its motion in and out of the upper casting. A locking device permits clamping the quill in any desired position. The carriage assembly provides the means for mounting and moving cutting tools. The

18、 carriage is a relatively flat H-shaped casting that rests and moves on the outer set of ways on the bed. The transverse bar of the carriage contains ways on which the cross slide is mounted and can be moved by means of a feed screw that is controlled by a small handwheel and a graduated dial. Through the cross slide a means is provided for moving