变频器设计使用参考外文翻译

《变频器设计使用参考外文翻译》由会员分享，可在线阅读，更多相关《变频器设计使用参考外文翻译（13页珍藏版）》请在毕设资料网上搜索。

1、河南理工大学万方科技学院本科毕业论文 1 河南理工大学万方科技学院 电气与自动化工程系 2012 届毕业生 英 文 文 献 专业： 电气工程及其自动化 班级： 08 电气 6 班 学号： 0828100023 姓名： 叶国印 时间： 2012 年 5 月 31 日 河南理工大学万方科技学院本科毕业论文 2 外文资料与中文翻译 外文资料： Converter reference design (1) Converter Selection: Selection to determine the frequency converter when the following points: 1) T

2、he purpose of a variable frequency； constant pressure to control or constant current control. 2) the load converter types such as leaves or pump volume pumps, with special attention to load the performance curve, the performance curve of the decision of the ways and means. 3) the frequency converter

3、 and load matching Voltage match: a rated voltage converter with a rated voltage line with the load. Current matches: ordinary pump, the rated current inverter and motor rated current match. For special load such as deep-water pumps, and so on need to refer to the electrical performance parameters t

4、o determine the most current inverter current and Guozainengli. Torque match: in this case constant torque load or slow down when the device may have occurred. 4) the use of high-speed motor drive inverter, because of the high-speed motor, anti-small, high harmonics lead to increased output current

5、value increases. So for high-speed motor inverter Selection, its capacity to be slightly larger than the ordinary motor selection. 5) If the frequency converter to a long cable run, this time to take measures to curb the long cable to the impact of capacitive coupling, inadequate efforts to avoid co

6、nverter, so in this case, the drive to enlarge the capacity of a file or the converter Output installed output reactor. 6) For the application of some special occasions, such as high temperatures, high altitude, at this time would cause the down converter capacity, the drive to enlarge the capacity

7、of a block. 河南理工大学万方科技学院本科毕业论文 3 (2) inverter control schematic design: 1) First confirmation of the installation environment Converter Operating temperature: high-power converter is the internal electronic components, vulnerable to the effects of temperature, product general requirements for 0 55 ,

8、 but in order to ensure the safe, reliable, the use of room to be taken into account, the best control in 40 below. In the control box, the converter box should generally be installed in the upper and strictly comply with the Manual of installation requirements, absolutely not be allowed to heating

9、elements or components easily fever close to the converter installed at the bottom. Ambient temperature: the temperature is too high and large temperature changes, within easy converter there is dew, the insulation properties will be greatly reduced, or even short-circuit caused the accident. When n

10、ecessary, to be added to the desiccant in the box and heater. In water treatment, generally heavier than water vapor, if the temperature changes, then this problem would be more prominent. Corrosive gases: the use of the environment if the corrosive gas concentrations, will not only lead corrosion o

11、f components, printed circuit boards, but it will also accelerate the aging of plastic devices, reducing insulation properties. Vibration and shock: the control cabinet with converter by vibration and mechanical shocks will cause electrical connection is bad. Huaian thermoelectric there such a probl

12、em. Apart from raising the control cabinet at this time of the mechanical strength, vibration and shock away from the source, we must also use seismic rubber pad fixed within and outside the control cabinet, such as electromagnetic switches have a vibration components. Equipment operation after a pe

13、riod of time and should conduct inspections and maintenance. Electromagnetic interference: Inverter at work due to rectification and frequency, produce around a lot of electromagnetic interference, these high-frequency electromagnetic waves in the vicinity of the instrument, apparatus, a certain interference. Therefore, the cabinet instrumentation and electronic systems, it should be optional metal, shielding the inverter instrument interference. All the components should be reliable grounding, in addition, the electrical components, equipment and