电气专业外文翻译---应用于电气系统的可编程序控制器

《电气专业外文翻译---应用于电气系统的可编程序控制器》由会员分享，可在线阅读，更多相关《电气专业外文翻译---应用于电气系统的可编程序控制器（25页珍藏版）》请在毕设资料网上搜索。

1、PDF外文： http:/  中文4280字外 文 翻 译     院   （系）   专业班级   姓     名   学     号   指导教师               年     月     日                       &nbs

2、p;                                                       第   2  页  Programmable designed for electro-pneumatic systems controller John F.Wakerly This

3、project deals with the study of electro-pneumatic systems and the programmable controller that provides an effective and easy way to control the sequence of the pneumatic actuators movement and the states of pneumatic system. The project of a specific controller for pneumatic applications join the s

4、tudy of automation design and the control processing of pneumatic systems with the electronic design based on microcontrollers to implement the resources of the controller. 1. Introduction The automation systems that use electro-pneumatic technology are formed mainly by three kinds of elements: actu

5、ators or motors, sensors or buttons and control elements like valves. Nowadays, most of the control elements used to execute the logic of the system were substituted by the Programmable Logic Controller (PLC). Sensors and switches are plugged as inputs and the direct control valves for the actuators

6、 are plugged as outputs. An internal program executes all the logic necessary to the sequence of the movements, simulates other components like counter, timer and control the status of the system.    With the use of the PLC, the project wins agility, because it is possible to create and si

7、mulate the system as many times as needed. Therefore, time can be saved, risk of mistakes reduced and complexity can be increased using the same elements. A conventional PLC, that is possible to find on the market from many companies, offers many resources to control not only pneumatic systems, but

8、all kinds of system that uses electrical components. The PLC can be very versatile and robust to be applied in many kinds of application in the industry or even security system and automation of buildings. Because of those characteristics, in some applications the PLC offers to much     &n

9、bsp;                                                                     第   3  页  resources that are not even used

10、 to control the system, electro-pneumatic system is one of this kind of application. The use of PLC, especially for small size systems, can be very expensive for the automation project. An alternative in this case is to create a specific controller that can offer the exactly size and resources that

11、the project needs 3, 4. This can be made using microcontrollers as the base of this controller.     The controller, based on microcontroller, can be very specific and adapted to only one kind of machine or it can work as a generic controller that can be programmed as a usual PLC and work w

12、ith logic that can be changed. All these characteristics depend on what is needed and how much experience the designer has with developing an electronic circuit and firmware for microcontroller. But the main advantage of design the controller with the microcontroller is that the designer has the tot

13、al knowledge of his controller, which makes it possible to control the size of the controller, change the complexity and the application of it. It means that the project gets more independence from other companies, but at the same time the responsibility of the control of the system stays at the des

14、igner hands 2. Electro-pneumatic system On automation system one can find three basic components mentioned before, plus a logic circuit that controls the system. An adequate technique is needed to project the logic circuit and integrate all the necessary components to execute the sequence of movemen

15、ts properly.  For a simple direct sequence of movement an intuitive method can be used 1, 5, but for indirect or more complex sequences the intuition can generate a very complicated circuit and signal mistakes. It is necessary to use another method that can save time of the project, make a clea

16、n circuit, can eliminate occasional signal overlapping and redundant circuits. The presented method is called step-by-step or algorithmic 1, 5, it is valid for pneumatic and electro-pneumatic systems and it was used as a base in this work.  The method consists of designing the systems based on standard circuits made