RFID技术外文文献翻译

《RFID技术外文文献翻译》由会员分享，可在线阅读，更多相关《RFID技术外文文献翻译（7页珍藏版）》请在毕设资料网上搜索。

1、 外文文献 Current RFID Technology This section describes out of which parts RFID tags consist of, how they work in principle, and what types of tags do exist. It focuses on how tags are powered and what frequency ranges is used. The section concludes by covering a few important standards. RFID transpond

2、ers (tags) consist in general of: Micro chip, Antenna, Case, Battery (for active tags only) The size of the chip depends mostly on the Antenna. Its size and form is dependent on the frequency the tag is using. The size of a tag also depends on its area of use. It can range from less than a millimete

3、r for implants to the size of a book in container logistic. In addition to the micro chip, some tags also have rewritable memory attached where the tag can store updates between reading cycles or new data like serial numbers. A RFID tag is shown in figure 1. The antenna is clearly visible. As said b

4、efore the antenna has the largest impact of the size of the tag. The microchip is visible in the center of the tag, and since this is a passive tag it does not have an internal power source In principle an RFID tag works as follows: the reading unit generates an electro-magnetic field which induces

5、a current into the tags antenna. The current is used to power the chip. In passive tags the current also charges a condenser which assures uninterrupted power for the chip. In active tags a battery replaces the condenser. The difference between active and passive tags is explained shortly. Once acti

6、vated the tag receives commands from the reading unit and replies by sending its serial number or the requested information. In general the tag does not have enough energy to create its own electro-magnetic field, instead it uses back scattering to modulate (reflect/absorb) the field sent by the rea

7、ding unit. Because most fluids absorb electro-magnetic fields and most metal reflect those fields the reading of tags in presence of those materials is complicated. During a reading cycle, the reader has to continuously power the tag. The created field is called continuous wave, and because the stre

8、ngth of the field decreases with the square of the distance the readers have to use a rather large power. That field overpowers any response a tag could give, so therefore tags reply on side-channels which are located directly below and above the frequency of the continuous wave. 1. Energy Sources W

9、e distinguish 3 types of RFID tags in relation to power or energy: Passive, Semi-passive, Active Passive tags do not have an internal power source, and they therefore rely on the power induced by the reader. This means that the reader has to keep up its field until the transaction is completed. Beca

10、use of the lack of a battery, these tags are the smallest and cheapest tags available； however it also restricts its reading range to a range between 2mm and a few meters. As an added benefit those tags are also suitable to be produced by printing. Furthermore their lifespan is unlimited since they

11、do not depend on an internal power source. The second type of tags is semi-passive tags. Those tags have an internal power source that keeps the micro chip powered at all times. There are many advantages: Because the chip is always powered it can respond faster tore quests, therefore increasing the

12、number of tags that can be queried per second which is important to some applications. Furthermore, since the antenna is not required for collecting power it can be optimized for back scattering and therefore increasing the reading range. And last but not least, since the tag does not use any energy

13、 from the field the back scattered signal is stronger, increasing the range even further. Because of the last two reasons, a semi-active tag has usually a range larger than a passive tag. The third type of tags is active tags. Like semi-active tags they contain an internal power source but they use

14、the energy supplied for both, to power the micro chip and to generate a signal on the antenna. Active tags that send signals without being queried are called beacons. An active tags range can be tens of meters, making it ideal for locating objects or serving as landmark points. The lifetime is up to

15、 5 years. 2. Frequency Bands RFID tags fall into three regions in respect to frequency: Low frequency (LF, 30- 500kHz), High frequency (HF.10-15MHz), Ultra high frequency (UHF, 850- 950MHz, 2.4-2.5GHz, 5.8GHz) Low frequency tags are cheaper than any of the higher frequency tags. They are fast enough

16、 for most applications, however for larger amounts of data the time a tag has to stay in a readers range will increase. Another advantage is that low frequency tags are least affected by the presence of fluids or metal. The disadvantage of such tags is their short reading range. The most common freq

17、uencies used for low frequency tags are 125-134.2 kHz and 140-148.5 kHz. High frequency tags have higher transmission rates and ranges but also cost more than LF tags. Smart tags are the most common member of this group and they work at 13.56MHz. UHF tags have the highest range of all tags. It range

18、s from 3-6 meters for passive tags and 30+ meters for active tags. In addition the transmission rate is also very high, which allows to read a single tag in a very short time. This feature is important where tagged entities are moving with a high speed and remain only for a short time in a readers r

19、ange. UHF tags are also more expensive than any other tag and are severely affected by fluids and metal. Those properties make UHF mostly useful in automated toll collection systems. Typical frequencies are 868MHz (Europe), 915MHz (USA), 950MHz (Japan), and 2.45GHz.Frequencies for LF and HF tags are

20、 license exempt and can be used worldwide； however frequencies for UHF tags differ from country to country and require a permit. 3. Standards The wide range of possible applications requires many different types of tags, often with conflicting goals (e.g. low cost vs. security). That is reflected in

21、 the number of standards. A short list of RFID standards follows: ISO11784, ISO11785, ISO14223, ISO10536, ISO14443, ISO15693, ISO18000. Note that this list is not exhaustive. Since the RFID technology is not directly Internet related it is not surprising that there are no RFCs available. There cent hype around RFID technology has resulted in an explosion in patents. Currently there are over 1800 RFID related patents issued (from