外文翻译--AT89S52的功能介绍

《外文翻译--AT89S52的功能介绍》由会员分享，可在线阅读，更多相关《外文翻译--AT89S52的功能介绍（17页珍藏版）》请在毕设资料网上搜索。

1、1 附录 外文资料 英文部分： The function introduction of AT89S52 Features(R) * Compatible with MCS-51 Products * 8K Bytes of In-System Programmable (ISP) Flash Memory Endurance: 1000 Write/Erase Cycles * 4.0V to 5.5V Operating Range * Fully Static Operation: 0 Hz to 33 MHz * Three-level Program Memory Lock * 25

2、6 x 8-bit Internal RAM * 32 Programmable I/O Lines * Three 16-bit Timer/Counters * Eight Interrupt Sources * Full Duplex UART Serial Channel * Low-power Idle and Power-down Modes * Interrupt Recovery from Power-down Mode * Watchdog Timer * Dual Data Pointer * Power-off Flag Description： The AT89S52

3、is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory. The device is manufactured using Atmels high-density nonvolatile memory technology and is compatible with the industry-standard 80C51 instruction set and pin-out .The on-chip Flash allow

4、s the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S52 is a powerful microcontroller which provides a highly-flexible and cost-effective solutio

5、n to many embedded control applications. The AT89S52 provides the following standard features: 8K bytes of Flash, 256 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, three 16-bit timer/counters, a six-vector two-level interrupt architecture, a full duplex serial port, on-chip oscillat

6、or, and clock circuitry. In addition, the AT89S52 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to continue functioning.

7、 The Power-down mode saves the RAM con-tents but freezes the oscillator, disabling all other chip functions until the next interrupt or hardware reset. Pin Description： VCC： Supply voltage. GND： Ground. 2 Port 0： Port 0 is an 8-bit open drain bidirectional I/O port. As an output port, each pin can s

8、ink eight TTL inputs. When 1s are written to port 0 pins, the pins can be used as high-impedance inputs. Port 0 can also be configured to be the multiplexed low-order address/data bus during accesses to external program and data memory. In this mode, P0 has internal pull-ups. Port 0 also receives th

9、e code bytes during Flash programming and outputs the code bytes during program verification. External pull-ups are required during program verification. Port 1： Port 1 is an 8-bit bidirectional I/O port with internal pull-ups . The Port 1 output buffers can sink/source four TTL inputs. When 1s are

10、written to Port 1 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source because of the internal pull-ups. current (I IL) In addition, P1.0 and P1.1 can be configured to be the timer/counter 2 external co

11、unt input (P1.0/T2) and the timer/counter 2 trigger input (P1.1/T2EX), respectively, as shown in the following table . Port 1 also receives the low-order address bytes during Flash programming and verification. Port Pin Alternate Functions P1.0 T2 (external count input to Timer/Counter 2), clock-out

12、 P1.1 T2EX (Timer/Counter 2 capture/reload trigger and direction control) P1.5 MOSI (used for In-System Programming) P1.6 MISO (used for In-System Programming) P1.7 SCK (used for In-System Programming) Port 2： Port 2 is an 8-bit bidirectional I/O port with internal pull-ups . The Port 2 output buffe

13、rs can sink/source four TTL inputs .When 1s are written to Port 2 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs ,Port 2 pins that are externally being pulled low will source because of the internal pull-ups .current (I IL) Port 2 emits the high-order addres

14、s byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX DPTR). In this application, Port 2 uses strong internal pull-ups when emitting 1s. During accesses to external data-memory that use 8-bit addresses (MOVX RI), Port 2 emits t

15、he contents of the P2 Special Function Register .Port 2 also receives the high-order address bits and some control signals during Flash programming and verification. Port 3： Port 3 is an 8-bit bidirectional I/O port with internal pull-ups .The Port 3 output buffers can sink/source four TTL inputs .W

16、hen 1s are written to Port 3 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs , Port 3 pins that are externally being pulled low will source because of the pull-ups .current (I IL) Port 3 also serves the functions of various special features of the AT89S52, as

17、 shown in the following table .Port 3 also receives some control signals for Flash programming and verification. Port Pin Alternate Functions P3.0 RXD (serial input port) P3.1 TXD (serial output port) P3.2 INT0 (external interrupt 0) P3.3 INT1 (external interrupt 1) P3.4 T0 (timer 0 external input)

18、P3.5 T1 (timer 1 external input) P3.6 WR (external data memory write strobe) 3 P3.7 RD (external data memory read strobe) RST： Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device. This pin drives high for 96 oscillator periods after the Watchdog t

19、imes out .The DISRTO bit in SFR AUXR (address 8EH) can be used to disable this feature. In the default state of bit DISRTO , the RESET HIGH out feature is enabled. ALE/PROG： Address Latch Enable (ALE) is an output pulse for latching the low byte of the address during accesses to external-memory. Thi

20、s pin is also the program pulse input (PROG) during Flash programming. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to external data mem

21、ory. If desired, ALE operation can be disabled by setting bit 0 of SFR location 8EH. With the bit set, ALE is active only during a MOVX or MOVC instruction. Otherwise, the pin is weakly pulled high. Setting the ALE-disable bit has no effect if the microcontroller is in external execution mode. PSEN：

22、 Program Store Enable (PSEN) is the read strobe to external program memory. When the AT89S52 is executing code from external pro- gram memory, PSEN is activated twice each machine activations are skipped during cycle, except that two PSEN each access to external data memory. EA/VPP： External Access

23、Enable. EA must be strapped to GND in order to enable the device to fetch code from external pro-gram memory locations starting at 0000H up to FFFFH. EA will be Note, however, that if lock bit 1 is programmed, internally latched on reset. EA should be strapped to V CC for internal program executions

24、 .This pin also receives the 12-volt programming enable volt-age (V PP) during Flash programming. XTAL1： Input to the inverting oscillator amplifier and input to the internal clock operating circuit. XTAL2： Output from the inverting oscillator amplifier. Special Function Registers： A map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 1. Table 1 . AT89S52 SFR Map and Reset Values