数控机床相关毕业设计翻译---通过热量误差补偿来改善数控机床的精确度

《数控机床相关毕业设计翻译---通过热量误差补偿来改善数控机床的精确度》由会员分享，可在线阅读，更多相关《数控机床相关毕业设计翻译---通过热量误差补偿来改善数控机床的精确度（11页珍藏版）》请在毕设资料网上搜索。

1、 IMPROVING ACCURACY OF CNC MACHINE TOOLS THROUGH COMPENSATION FOR THERMAL ERRORS Abstract： A method for improving accuracy of CNC machine tools through compensation for the thermal errors is studied. The thermal errors are obtained by 1-D ball array and characterized by an auto regressive model base

2、d on spindle rotation speed. By revising the workpiece NC machining program , the thermal errors can be compensated before machining. The experiments on a vertical machining center show that the effectiveness of compensation is good. Key words : CNC machine tool Thermal error Compensation 0 INTRODUC

3、TION Improvement of machine tool accuracy is essential to quality cont rol in manufacturing processes. Thermally induced errors have been recognized as the largest cont ributor to overall machine inaccuracy and are probably the most formidable obstacle to obtaining higher level of machine accuracy.

4、Thermal errors of machine tools can be reduced by the st ructural improvement of the machine tool it self through design and manufacturing technology. However , there are many physical limitations to accuracy which can not be overcome solely by production and design techniques. So error compensation

5、 technology is necessary. In the past several years , significant effort s have been devoted to the study. Because thermal errors vary with time during machining ,most previous works have concent rated on real-time compensation. The typical approach is to measure the thermal errors and temperature o

6、f several representative point s on the machine tools simultaneously in many experiment s , then build an empirical model which correlates thermal errors to the temperature statues by multi-variant regression analysis or artificial neural network.During machining , the errors are predicted on-line a

7、ccording to the pre-established model and corrected by the CNC cont roller in real-time by giving additional signals to the feed-drive servo loop.However , very few practical cases of real-time compensation have been reported to be applied to commercial machine tools today. Some difficulties hinder

8、it s widespread application. First , it is tedious to measure thermal errors and temperature of many point s on the machine tools. Second ,the wires of temperature sensors influence the operating of the machine more or less. Third , thereal-time error compensation capability is not available on most

9、 machine tools. In order to improve the accuracy of production-class CNC machine tools , a novel method is proposed. Although a number of heat sources cont ribute to the thermal errors , the f riction of spindle bearings is regarded as the main heat source. The thermal errors are measureed by 1-D ba

10、ll array and a spindle-mounted probe. An auto regressive model based on spindle rotation speed is then developed to describe the time-variant thermal error. Using this model , thermal errors can be predicted as soon as the workpiece NC machining program is made. By modifying the program , the therma

11、l errors are compensated before machining. The effort and cost of compensation are greatly reduced. This research is carried on a JCS2018 vertical machining center. 1 EXPERIMENTAL WORK For compensation purpose , the principal interest is not the deformation of each machine component , but the displa

12、cement of the tool with respect to the workpiece. In the vertical machining center under investigation , the thermal errors are the combination of the expansion of spindle , the distortion of the spindle housing , the expansion of three axes and the distortion of the column. Due to the dimensional e

13、longation of leadscrew and bending of the column , the thermal errors are not only time-variant in the time span but also spatial-variant over the entire machine working space. In order to measure the thermal errors quickly , a simple protable gauge , i. e. , 1-D ball array , is utilized. 1-D ball a

14、rray is a rigid bar with a series of balls fixed on it with equal space. The balls have the same diameter and small sphericity errors. The ball array is used as a reference for thermal error measurement . A lot of pre-experiment s show that the thermal errors in z-axis are far larger than those in x

15、-axis and y-axis , therefore major attention is drawn on the thermal errors in z-axis. Thermal errors in the other two axes can be obtained in the same way. The measuring process is shown in Fig.1. A probe is mounted on the spindle housing and 1-D ball array is mounted on the working table. Initiall

16、y , the coordinates of the balls are measured under cold condition. Then the spindle is run at a testing condition over a period of time to change the machine thermal status. The coordinates of the balls are measured periodically. The thermal drift s of the tool are obtained by subt racting the ball

17、 coordinates under the new thermal status f rom the reference coordinates under initial condition. Because it takes only about 1 min to finish one measurement , the thermal drifts of the machine under different z coordinates can be evaluated quickly and easily. According to the rate of change , the

18、thermal errors and the rotation speed are sampled by every 10 min. Since only the drift s of coordinates deviated from the cold condition but not the absolute dimensions of the gauge are concerned , accuracy and precise inst rument such as a laser interferometer is not required. There are only four

19、measurement point s z 1 ,z 2 , z 3 , z 4 to cover the z-axis working range whose coordinates are - 50 , - 150 , - 250 , - 350 respectively. Thermal errors at other coordinates can be obtained by an interpolating function. Previous experiment s show that the thermally induced displacement between the

20、 spindle housing and the working table is the same with that between the spindle and table. So the thermal errors z measured reflect those in real cutting condition with negligible error. In order to obtain a thorough impression of the thermal behavior of the machine tool and identify the error model accurately , a measurement strategy is developed. Various loads of the spindle speed are applied. They are divided into three categories as the