1、外文翻译 1 Translated from: XiongFusheng, DC Switching Power Supply Protection Technology, Guangzhou:The World of Power Supply P,2002.2. DC Switching Power Supply Protection Technology Abstract: The DC switching power supply protection system, protection system design principles and machine protection m
2、easures, an analysis of switching power supply in the range of protected characteristics and its design methodology,introduced a number of practical protection circuit. Keywords: switching power supply protection circuit system design 1、 Introduction DC switching regulator used in the price of more
3、expensive high-power switching devices, the control circuit is also more complex, In addition, the load switching regulators are generally used a large number of highly integrated electronic systems installed devices. Transistors and integrated device tolerance electricity, less heat shocks. Switchi
4、ng Regulators therefore should take into account the protection of voltage regulators and load their own safety. Many different types of circuit protection, polarity protection, introduced here, the program protection, over-current protection, over-voltage protection, under-voltage protection and ov
5、er-temperature protection circuit. Usually chosen to be some combination of protection, constitutes a complete protection system. 2、 polarity protection DC switching regulator input are generally not regulated DC power supply. Operating errors or accidents as a result of the situation will take its
6、wrong polarity, switching power supply will be damaged. Polarity protection purposes, is to make the switching regulator only when the correct polarity is not connected to DC power supply regulator to work at. Connecting a single device can achieve power polarity protection. Since the diode D to flo
7、w through switching regulator input total current, this circuit applied in a low-power switching regulator more suitable. Power in the larger occasion, while the polarity protection circuit as a procedure to protect a link, save the power required for polarity protection diodes, power consumption wi
8、ll be reduced. In order to easy to operate, make it easier to identify the correct polarity or not, collect the next light. 宽输入电压高频开关电源的设计 2 3、 procedures to protect Switching power supply circuit is rather complicated, basically can be divided into low-power and high-power part of the control part
9、of the switch. Switch is a high-power transistors, for the protection of the transistor switch is turned on or off power safety, we must first modulator, amplifier and other low-power control circuit. To this end, the boot to ensure the correct procedures. Switching Regulators generally take the inp
10、ut of a small inductor, the input filter capacitor. Moment in the boot, filter capacitor will flow a lot of surge current, the surge current can be several times more than the normal input current. Such a large surge current may contact the general power switch or relay contact melting, and the inpu
11、t fuse fuse. In addition, the capacitor surge current will damage to shorten the life span of premature damage. To this end, the boot should be access to a current limiting resistor, through the current limiting resistor to capacitor charging. In order not to make the current limiting resistor exces
12、sive power consumption, thus affecting the normal switching regulator, and the transient process in the boot after a short period then automatically relays it to DC power supply directly to the switching regulator power supply. This circuit switching regulator called a soft start circuit. Switching
13、regulator control circuit of the logic components required or op-amp auxiliary power supply. To this end, the auxiliary power supply must be in the switch circuit. This control circuit can be used to ensure the boot. Normal boot process is: to identify the polarity of input power, voltage protection
14、 procedures boot auxiliary power supply circuit and through current limiting resistor R of the switching regulator input capacitor C charge modulation switching regulator circuit, short -circuit current limiting resistor stability switching regulator. In the switching regulator, the machines just be
15、cause the output capacitance, and charge to the rated output voltage value of the need for a certain period of time. During this time, sampling the output amplifier with low input voltage sampling, closed-loop regulation characteristics of the system will force the switching of the transistor conduc
16、tion time lengthened, so that switching transistor during this period will tend to continuous conduction, and easily damaged. To this end, the requirements of this paragraph in the boot time, the switch to switch the output modulation circuit transistor base drive signal of the pulse width modulatio
17、n, can guarantee the switching transistor by the cut-off switches are becoming 外文翻译 3 more and more normal state, therefore the protection of the setting up of a boot to tie in with the soft start. 4、 over-current protection When the load short-circuit, overload control circuit failure or unforeseen
18、 circumstances, such as would cause the flow of switching voltage regulator transistor current is too large, so that increased power tubes, fever, if there is no over-current protection device, high power switching transistor may be damaged. Therefore, the switching regulator in the over-current pro
19、tection is commonly used. The most economical way is to use simple fuse. As a result of the heat capacity of small transistors, general fuse protection in general can not play a role in the rapid fuse common fuse. This method has the advantage of the protection of vulnerable, but it needs to switch
20、transistor in accordance with specific security requirements of the work area to select the fuse specifications. This disadvantage is over-current protection measures brought about by the inconvenience of frequent replacement of fuses. Linear voltage regulator commonly used in the protection and cur
21、rent limiting to protect the cut-off in the switching regulator can be applied. However, according to the characteristics of switching regulators, the protection circuit can not directly control the output transistor switches, and overcurrent protection must be converted to pulse output commands to
22、control the modulator to protect the transistor switch. In order to achieve over-current protection are generally required sampling resistor in series in the circuit, this will affect the efficiency of power supply, so more for low-power switching regulator of occasions. In the high-power switching
23、power supply, by taking into account the power consumption should be avoided as far as possible access to the sampling resistor. Therefore, there will usually be converted to over-current protection, and under-voltage protection. 5、 over-voltage protection Switching regulators input over-voltage pro
24、tection, including over-voltage protection and output over-voltage protection. Switching regulator is not used in DC power supply voltage regulator and rectifier, such as battery voltage, if too high, so switching regulator is not working properly, or even damage to internal devices, therefore, it is necessary to use the input over-voltage protection circuit. Using transistors and relays protection circuit. In the circuit, when the input DC power supply voltage higher than the voltage regulator diode breakdown voltage value, the breakdown voltage regulator tube, a current
